Standard Ultrasonic Plastic Welding Machine

turn dish high frequency plastic welding equipment :electric-hot efficiency high ,cover land small , operation simple .... - details see: https://www.machineto.com/standard-ultrasonic-plastic-welding-machine-10139262
Place of Origin:Jiangsu China (Mainland)Brand Name:shuangchaoModel Number:XDVoltage:220V/50HZ
Power:1500WFrequency:20KHzWelding Area:150*150mmDimensions:750*500*1200
Weight:110KGUsage:plastic welding machineAfter-sales Service Provided:Overseas service center available 
Standard Ultrasonic Plastic Welding Machine
contact supplier for Standard Ultrasonic Plastic Welding Machine


Sequence of operations
1), The power cord connected to the machine, open the lower part of the power switch oscillator;
2), The control box (in the compression machine above) while the power switch indicator light, while the cooling fan rotation, but must be operational after about 10 minutes too.
3), set the tuner to "0" position, to be covered with insulation cloth and then put the tape on the plate welding;
4), Told in the hold mode control device (BAR HOLDEL) materials in or on it, and then the level of the screw to adjust the level height.
5), Step under the pressure on the pedal pressure on the material and also examine the

mold and the lower fixed disk are smooth.
6), The putter head moving and adjusting the level of Songjiang turned the plum to the mold level.
7), Rotating the head back in time to mold the plum increased to a minimum at the foot clockwise and the Ministry of plum to fall to the lowest point of the mold so that the head bolt tightening with a sense of plum, and then foot pipe will be automatically spring back to power transmission.
8), The sample placed in floor operating machinery, the operation is completed, its foot pipe will be automatically bounced back to power transmission.
9), when the pedal tube homing operation should automatically spring back, such as the failure adjust the pressure setting slightly clockwise to produce effect immediately.
10), The samples were placed in floor, operating machinery, depress the foot control, there is pressure to produce two before labor-saving devices to achieve results if not please re-adjust the repeat (7) action.
11), Continue (5) of the action, take a look at current meter foot pedal to make it oscillate.
12). High-speed oscillation Harmonic beginning to turn the pointer slowly from the "0" to "100."
13), When the tuner turn to the appropriate location to stop rotating, the tuner of the operation is the action by the ammeter pointer mold according to the size of the electrode and the thickness of PVC vary.
14), In a few seconds to move the pointer to move the red line, this time to relax after a foot switch, two seconds to cool down, relax pressure on the pedal.
15), Welding is complete, view the situation and adjust the level of welding and tuning, if the experiment many times with the timer switch will be necessary to switch the location of time, once the calibration timer switch to keep the pressure on the foot pedal until the oscillator stops, If you have not yet reached in the calibration of the time, the cut off high-frequency current, as long as you can relax at any time cut off the foot switch high-frequency current.
16), when the work is completed, cut off the main switch (MAIN LINE SWTTCH) and the main switch.
3,Operating reference:
When the tuner tuned over into the meter pointer over the red line, the tube of the load beyond the capacity limit, the power switch off the load current is automatically cut off by a relay or brakes, this case back to the same tune can be a little bit to Weld.When there are defects in the material, not fixing a flat mold or materials on the dust, may cause sparks, which must be in operation before the review and adjustment.

Designing of welding line

Samples of ultrasonic welding

Standard Ultrasonic Plastic Welding Machine
Packaging Detail:wooden box
Delivery Detail:in 5 days after your confirmed payment

Related Product for Standard Ultrasonic Plastic Welding Machine