Small family use 48 full automatic chicken egg incubator sale

Technical Specification

1. Testing you unit for the first time:

1.1 Connect the egg turner plug to the control plug inside the egg compartment.

1.2 Connect the provided power supply to the back of the unit and your power source.

1.3 Switch on your power source.

1.4 Switch your unit on.

1.5 You will hear an alarm sounding due to low temperature/humidity.

1.6 Press any of the green buttons to cancel the alarm.

1.7 By opening the incubator and filling the water channels you will notice the humidity reading increase.

1.8 Let the unit run for 2 hours to note the egg turner turning.

2. Setting the temperature

2.1 Push “SET” once.

2.2 Push “+” or “-“ to select the desired temperature.

2.3 Push “SET” once more to exit.

oC, I found the chicks hatch at day 19 to

20 meaning the temperature being to high. Using the method as described

above. I recommend you set the temperature at 37.6oC.

3. Temperature alarm parameter settings (AL and AH)

oC over or below the set temperature. This is sufficient and you do not need to make any changes to these settings.

3.1 Low temperature alarm parameter setting. (AL)

3.1.1 Press and hold “SETT” for 3 sec.

3.1.2 Push “+” or “-“ until code “AL” appears in the temperature screen.

3.1.3 Push “SET”

3.1.4 Push “+” or “-“ to adjust to your desired lower alarm setting.

3.2 Higher temperature alarm parameter setting (AH)

3.2.1 Press and hold “SETT” for 3 sec.

3.2.2 Push “+” or “-“ until code “AH” appears in the temperature screen.

3.2.3 Push “SET”

3.2.4 Push “+” or “-“ to adjust to your desired higher alarm setting.

4. Humidity alarm parameter settings (AS)

4.1 Low humidity alarm parameter setting. (AS)

4.2 Press and hold “SETT” for 3 sec.

4.3 Push “+” or “-“ until code “AS” appears in the temperature screen.

4.4 Push “SET”

4.5 Push “+” or “-“ to adjust to your desired lower alarm setting.- By filling both water channels the humidity should rise to 60% dependant on the local humidity levels and the time of year. I tend to fill both my water channels every 4 to 5 days and at day 18 when I remove the egg trays I over fill them to increase the humidity to about 65%.

5. Calibrating temperature sensor reading(CA)

The thermometer correct reading is set at 0oC. The reading given by the thermometer can be adjusted if you find that the temperature reading is incorrect using a calibrated thermometer.

5.1 Calibrating the temperature sensor measurement. (CA)

5.2 Press and hold “SETT” for 3 sec.

5.3 Push “+” or “-“ until code “CA” appears in the temperature screen.

5.4 Push “SET”

5.5 Push “+” or “-“ to adjust to the correct measurement.

- Note that the adjustment is the difference between the thermometer readings

and should be adjusted with “- “ if the temperature reading of the incubator is to

high and normal value (indicating + value) if the incubator reading is too low.

6. Temperature Upper and lower limit set(HS and LS)

HS- (High Set) andLS- (Low Set) set the limit of the setting range of the desired temperature setting (incubating temperature adjustment)

- This is to prevent accidental out of range temperature setting.

7. Heating Element(HU and HD)

HU -Default setting is 18 ( I believe it’s Heat Up power setting, controlling the start up power to the heater to bring it up to the desired temperature setting (incubating temperature adjustment). Setting Range 1~90.

HD -Default setting is 11 ( I believe it’s Heat Down power setting, controlling the power to maintain the heater at the desired temperature setting (incubating temperature adjustment).

Setting Range 1~80.

- These are settings I have never adjusted or attempted to adjust as the heating

unit starts and stops within 1oC of my set temperature of 37.6oC.

8. Display Symbols

9. Using your Incubator

1. Test your incubator to see if it functions properly.

2.Connect the egg turner plug to the control plug inside the egg compartment.

3. Fill one or both water channels depending on local humidity levels.

4. Set the eggs with the pointy side down.

5. Close the lid and switch on the incubator.

6. Press the reset button (left green button) to reset and start the day counter from “0”.

(this will also rest the egg turning countdown back to 1:59)

7. Keep an eye on the humidity reading and fill the water channels when needed.

(normally every 4 days)

8. At day 18 you should remove the tray with the turning mechanism and place the

eggs on top of he bottom grid.

9. At the same time it is important to fill both water channels to increase thehumidity. (this is very important to ensure that the eggshells are soft enough for

the chicks to break through.)

10.You should never open the lid when the chicks start to hatch. If you do, the loss ofhumidity will cause the eggshells of the unhatched eggs to dry out and they won’table to break through the egg.