Home  >  Metal Processing Machinery  >  Metal & Metallurgy Machinery  >  Rolling Mill

1.high performance dryer, 2.easy to install in work site, rotary kiln construction / lime kiln construction / cement kiln types - details see: https://www.machineto.com/roll-mill-roll-mill-rod-mills-10169598

Drier / rotary drier / driers

Drier Introduction:

Drier is mainly used for drying wet materials in building construction, metallurgy, chemical industries, and it can dry various materials with strong adaptability. Besides, it is common drying device in cement plant with simple and reliable operation.

In our company, this series applies the new type scatter plate device; it can guide direction, flow on an average and scatter the material and so on. And it can make the material in the thin, average and complete condition. Contact the heat airflow completely and use the heat energy fully. Moreover, it adopts reasonable operational parameter, and compared with general drier, it reduce the coal and power consumption above10-15%,and increase the output above10-15%. At present, it is widely used in cement and mining industries.

Working principle:

It mainly consists of revolution body, raise material board, transmission device, supportive device and sealing ring, etc.

The heat sources of the drier is from the combustion train, and is adopts down-flow heating methods. When the materials enter into the body from the feeding device, it will be pushed back by the spire raising board. As the drier is in an inclined position, the materials will be down to the lower end under the influence of gravity and rotation, but the raising board will be threw to the upper end for scattering. This procession makes the material well-distributed in the body, and then ensure the heat exchange with the heat wind. After repeated cycle with this procession, the moisture content will be dried.

Features and Benefits:

1. Reasonable design of raising board and angle ensure the material well-distributed and dry with less times, it has reliable operation and high energy utilization ratio, simple maintenance.
2. Adopt an adjustable center tug structure, the good cooperation of the tug and the rolling ring reduce the attrition and energy consumption.
3. The special structure of the dam-wheel decrease the horizontal thrust, when the machine working in inclination station, it has strong ability of anti-overloading, steady operation and high reliability.
4. High temperature resistance, it can use the high temperature to dry the material quickly,
5. Large capacity, few fuel consumption, low drying cost.

Features and Benefits:

1. High heat exchange rate, low energy consumption
2. Strong adaptability, large capacity
3. High aerated rate, low pressure drop, high operating spring and big interface
4. Reliable performance, easy operation, Wide range of application

Model	Basic Parameters				Power(kw)	Production Capacity(t/h)	Weight (kg)
	Inner Diameter (m)	Length(m)	Gradient (%)	Rotate Speed (r/min)
Φ0.6x6	0.6	6	5.0	3-8	3	0.5-2.0	2900
Φ0.8x8	0.8	8	5.0	3-8	4	0.8-2.5	3500
Φ0.8x10	0.8	10	5.0	3-8	4	1.0-3.5	4500
Φ1.0x10	1.0	10	5.0	3-8	5.5	1.5-6	5600
φ1.2×6	1.2	6	5.0	5.8	5.5	8	9380
Φ1.2x8	1.2	8	5.0	5.8	5.5	12	10200
φ1.5×12	1.5	12	5.0	4.8	15	12	16450
Φ1.5x15	1.5	15	5.0	4.8	15	16	18240
φ1.8×12	1.8	12	5.0	4.5	18.5	18	20000
Φ1.8x14	1.8	14	5.0	4.5	18.5	20	21000
φ2.2×12	2.2	12	5.0	4.3	22	22	37100
Φ2.2x14	2.2	14	5.0	4.3	22	28	38

roll mill / roll +mill / rod +mills

\ roll mill / roll +mill / rod +mills

roll mill / roll +mill / rod +mills