Fiat New holland 480

Fiat New Holland 480-S (Standard) 55 HP (2wd) Specifications

Most economical in 50 HP range.
Rugged, maneuverable and compact.
Easy accessibility to service points.

ENGINE POWER:
At flywheel 55 HP

OPERATING WEIGHT:
1,710 KG

SPEEDS (KPH)

With Tyres Engine Speed (rpm) Pto Speed (rpm) Forward First Second Third Fourth Fifth Sixth Seventh Eight Reverse First Second

2,160 540 1.87 2.82 4.13 5.33 6.75 10.15 14.86 19.20 2.69 9.70

12.4/11-28 2,500 625 2.17 3.26 4.78 6.17 7.81 11.75 17.20 22.22 3.11 11.22

ENGINE:

New Holland 8035.06
4-Stroke, direct injection diesel engine
Number of cylinder:	3
Bore and stroke:	100 x 115 mm
Piston Displacement:	2,710 cc
Compression ratio:	17:1
Max. Torque at 1,500 rpm:	22.7 kgm
Dry-type cylinder liners
Water cooled, Four-row brass tube & copper fin radiator
Forced-feed lubrication system
Distributor-type fuel injection pumps with mechanical speed governor
Vertical exhaust muffler

FILTERS
Air:Oil-bath with pre-cleaner and semiautomatic dust unloader.
Fuel:2 replaceable cartridges.
Oil:Easy-to-change, continuous flow cartridge.

CLUTCH
Dual plate, dry-type, with separate controls (pedal for transmission and hand lever for PTO), diameter of plates: 11 inch
Plate facing of asbestos compound

TRANSMISSION:
Gear box with constant-mesh gears: 8 forward and 2 reverse speeds;
Synchromesh on 3rd, 4th, 7th and 8th
speeds Differential with pedal actuated lock and automatic disconnection Single-reduction spur gear final drives Gear Box mounted starter safety switch

THREADS
Front (8 position):
1.320 - 1,420 - 1,520 - 1,620- 1,720 - 1,820 - 1,920 - 2,020 mm

Rear (8 position):

1,200 - 1,300 - 1,400 - 1,500- 1,600 - 1,700 - 1,800 - 1,900 mm

STEERING
Manual, recirculating ball type, centre relay lever, joints lubricated for life

POWER TAKE-OFF
6 spline shaft - 35 mm dia / 1-3/8"
Fully independent: 540 rpm at 2,160 engine rpm
High-speed DTO (*) 35 mm dia / 1-3/8"
same speed as engine rpm
(*) For application of high speed implements.

HYDRAULICS LIFT
With draft and position control, Draft control through top link, Gear type hydraulic pump driven from engine crankshaft, Pump capacity: 22.7 l/min Relief value opening pressure: 150-170 kg/sq. Cm 3-point linkage Cat I-II Manual response control Lower links with sway restrictors Control Lever with safety stop. Max. Lifting capacity: 1,450 kg

BRAKES
Service dry band-type with mechanical control Parking: with hand lever

CAPACITY

Fuel tank: Engine oil: Hydraulic Transmission: Rear Axle: Air Cleaner:

54 ltr 08 ltr 18 ltr 2+2 ltr at sides 01 ltr

TYRES

Front: Rear:

6.00-16 12.4/11-28

BODY
Hood has side-hinged cover for engine inspection. Front grill is easily removable for quick access to air cleaner and battery

ENGINE
Cold starting aid (Thermostat)
Radiator screen

LIGHTING SYSTEM
With 3-position headlights, plough lamp, blue high beam warning light on dashboard, low oil pressure warning light

LIGHTING SYSTEM
12 Volt starting system, 4hp starter motor, 400 watts alternator, 100 ah battery.
Canopy, Towing hook, Swinging Draw bar, Cold Starting aid, Front weight, High Clearance Kit, Low Clearance Kit, DTO pump applications and Creeper gear etc.

BELT PULLEY
Diameter: 250mm
Width: 150mm
Pulley speed: 1350 rpm
Belt Speed: 17.7 m/sec

OPTIONAL
AC Cabin, Canopy, Towing hook, Swinging Draw bar, Cold Starting aid, Front weight, High Clearance Kit, Low Clearance Kit, DTO pump applications and Creeper gear etc.